As I noticed from the comments, when trying to open the settings of a router, or a modem at 192.168.1.1 or 192.168.0.1 (perhaps you have a different address), users most often encounter such errors: "No Internet connection", "No access to the network "," There is no connection to the router ", etc. These errors appear in the browser when we type the address of the router in the address bar and click on it. It should be noted that this does not have to be an IP address. Now, most manufacturers indicate addresses like tplinkwifi.net, tendawifi.com, my.keenetic.net, etc. on the case of the router. And when we type this address in the browser, we can also encounter an error that there is no Internet connection, or no access to the network. And, of course, you cannot enter the router settings.
I myself have faced this problem more than once. It looks something like this: open a browser, type in the address of the router (usually 192.168.1.1 or 192.168.0.1), go to and see a message that there is no Internet connection, the page cannot be displayed, access to the site, the page is not available, or not found. The message itself may be different depending on the browser, settings, and your hardware.
Or like this:
Let me remind you that the error may be different. The main problem - the page with the router settings does not open
Let's consider two separate cases:
- When an error in the browser "says" there is no Internet connection, or network.
- When an error appears that the site cannot be opened, page 192.168.1.1 (or another address) is displayed, the site is not available, or something like that.
Look carefully and check everything.
How to open 192.168.1.1 and 192.168.0.1 if there is no internet connection?
I wrote about this in the article: how to set up a Wi-Fi router (go to settings) without the Internet. Consider these solutions in the event that you get an error about the lack of an Internet connection.
Important! I have already written about this more than once, but still I will repeat myself. In order to open a page with settings for a router, or a modem (the so-called web interface), Internet access is not needed. All that is needed is for your computer, laptop, or mobile device to be connected to the router. Via a network cable or Wi-Fi network.
Therefore, if you are trying to open the settings of the router and see an error that there is no access to the Internet, then first of all, make sure that your device is connected to the router itself.
If you have a PC or laptop, then the connection status should be as follows (depending on the connection with the router):
If you have the same connection status, then everything is in order, and the page with the router settings should open. If there is a red cross, or an asterisk next to the Wi-Fi network, then you need to check the connection. The best thing, of course, is to connect to the router via cable. Something like this:
Or over a Wi-Fi network. If the network is protected, the factory password (PIN) is indicated on a sticker on the router.
If possible, try connecting to the router from a different device.
If the page at the address 192.168.1.1 or 192.168.0.1 is not available
In this case, the browser will display a message that the page or site of the router is unavailable. Something like this:
Again, the error itself may be different if your browser is different.
It is important that the computer is connected only to the router, in the settings of which we need to go. If, for example, a cable connection, then Wi-Fi must be turned off (it is on your device). And vice versa.
There will be more solutions in case of such an error.
Solution # 1: check the router address
We need to make sure that we are trying to open the router settings to the correct address. In most cases, the factory address for accessing the control panel is indicated on the router itself. There will most likely be an IP address 192.168.1.1, 192.168.0.1, or an address from letters. For example, tplinkwifi.net. It looks like this:
I wrote in more detail on this topic in the article: How to find out the IP address of a router.
You may also find the following articles useful:
- 192.168.0.1 - the entrance to the router, or modem. admin and admin
- 192.168.1.1 or 192.168.0.1 - go to the Wi-Fi router settings
Sometimes it happens that the wizards change the IP address of the router during configuration. In this case, try opening Explorer (My Computer) and right-clicking on your router on the network tab. From the menu, select "View Device Webpage".
A browser with a router page should open automatically. We figured out the definition of the address. If you still cannot open the settings, then try other solutions.
Solution # 2: check your IP settings
By default, almost every router issues an IP address automatically. It runs a DHCP server. Therefore, it is important that the settings for automatically obtaining an IP address are set in the properties of your connection.
Go to "Network Connections". You can press Win + R and run the commandncpa.cpl
Further, depending on whether you have a router connected via cable or Wi-Fi, right-click on "Local Area Connection" (in Windows 10 - Ethernet), or "Wireless Network" and select "Properties". For example, I have a Wi-Fi connection.
And then we set the automatic receipt of addresses.
After that, we try to open the router settings. You can restart your computer and try again.
Or just do a network reset.
Solution # 3: enter the correct address to access the router
The fact is that the address at which you can access the control panel of the router must be entered in the address bar of the browser. Now, in many browsers, the address bar and the search search bar are the same string. And we most often type an address without http: //... Because of this, many instead of a router page open Yandex, Google, or another peak system.
Therefore, if you cannot access the page with the settings of the router, first of all try to open it in another browser. If, for example, in the Opera does not work, then we go through Chrome. Better yet, via Internet Explorer, or Microsoft Edge on Windows 10.
Let me remind you that we enter the address of the router in the address bar.
Or try to write the address withhttp: //... For instance:http://192.168.0.1, http://192.168.1.1, http://tplinkwifi.net.
Everything should work out.
If you still do not have a connection to the router, and when you go to the router's address, an error appears that the page is unavailable or there is no Internet connection, then describe your problem in the comments below. Be sure to write what kind of router and model you have. Well, before that, try the tips I wrote about above.
